Home>Products> Internal Combustion (IC) Forklift > Euro V / Stage V Compliant

Euro V Heavy Duty Forklift 25 Ton

• 25,000 kg rated load capacity
• 1,220 mm rated load center
• 4,000 mm standard lift height
• 5,940 mm maximum working height
• 2,400 × 285 × 110 mm forks
• 35,000 kg operating weight
• 160–162 kW engine power range
• 25 / 30 km/h loaded / unloaded speed
• 6,480 mm minimum turning radius
• Compliance documents matched to engine

Send Inquiry

Description

25-ton diesel counterbalance platform

High-capacity handling with compliance defined at engine level

The Euro V Heavy Duty Forklift 25 Ton is specified for a 25,000 kg rated load at a 1,220 mm load center, with a 4,000 mm standard lift and a 160–162 kW diesel power range. It is intended for engineered handling of large industrial loads where capacity, load geometry, yard access and destination-market emissions documentation must be evaluated together.

The photographed unit carries a wide lifting beam with hooks. The standard data also lists 2,400 mm forks, so the attachment and its residual capacity must be treated as project-specific until confirmed in the signed configuration.

Get Expert Advice

25,000 kgRated capacity

1,220 mmRated load center

4,000 mmStandard lift height

35,000 kgOperating weight

Start with the load case, not the tonnage label

A 25-ton rating is meaningful only when the real load center and attachment match the approved capacity chart.

The stated capacity applies at a 1,220 mm load center. Long steel structures, dies, machinery sections and project cargo can move the center of gravity farther forward or to one side. That changes residual capacity and stability even when the gross load remains below 25,000 kg.

Provide load weight, dimensions and center-of-gravity position.
Identify whether the load is palletized, cradled or suspended.
State the required fork spacing, attachment and lift height.
Include any side offset or restricted approach angle.
Request the load chart for the final mast and attachment.

Important capacity boundary

Do not apply the 25,000 kg figure to an unknown load center. The lifting beam visible in the photos introduces different forces from a pair of forks, while any attachment weight also reduces usable capacity.

Final approval should be based on the manufacturer's configuration drawing and rated-capacity chart, not on the page headline alone.

Specify Stage V evidence precisely

For regulated markets, the engine family and its approval documents matter more than a general emissions label.

Engine identityManufacturer, exact model, rated power and engine family

Approval referenceApplicable type-approval number and emissions marking

After-treatmentInstalled system and operating requirements for the selected engine

Delivery documentsCopies matched to the serial-numbered production configuration

The available power range is listed as 160–162 kW with Weichai or Cummins selection. The exact engine model and emissions package should be fixed in the quotation before any compliance statement is placed in a tender or import file.

Technical specification

Use these values for preliminary comparison, then reconcile them with the approved configuration sheet.

Rated load capacity	25,000 kg
Rated load center	1,220 mm
Operating weight	35,000 kg
Wheelbase	4,400 mm
Overall width	3,070 mm
Minimum turning radius	6,480 mm
Loaded gradeability	20%

Standard lift height	4,000 mm
Maximum working height	5,940 mm
Fork dimensions	2,400 × 285 × 110 mm
Fork carriage width	3,000 mm
Travel speed, loaded / unloaded	25 / 30 km/h
Maximum loaded lifting speed	260 mm/s
Engine power range	160–162 kW

Performance values depend on the approved machine, mast, attachment, tyres, surface and operating conditions.

Understand the photographed configuration

Side view of orange 25 ton diesel forklift fitted with a wide lifting beam and hooks

The photographed truck is fitted with a wide beam and multiple lifting points; confirm whether this attachment is included in the quotation.

Items visible in the product photos

Heavy counterbalance chassis with an enclosed cab
Large industrial tyres for outdoor paved-yard duty
High-positioned operator compartment and access steps
Front attachment with a wide beam and multiple hooks
Mast-mounted hydraulic lines and lifting structure

Match the truck to its working envelope

High-capacity outdoor handling needs enough pavement capacity, maneuvering space and visibility around the complete load.

Load interface

Forked or suspended

Define fork pockets, cradle design or lifting points. Suspended loads require an approved attachment and operating method.

Yard geometry

Turn and approach

Compare the 6,480 mm turning radius and 3,070 mm truck width with aisles, trailers, stored materials and exclusion zones.

Ground condition

Pavement and gradient

Verify bearing capacity for the 35,000 kg truck plus load, along with drainage, joints, potholes and the actual travel gradient.

Suitable project profiles

Heavy machinery components with defined lift points
Steel products supported by approved pallets or cradles
Large molds, dies and fabricated assemblies
Port and industrial-yard project cargo
Construction materials within the approved load chart

Operator view inside the enclosed cab of the 25 ton heavy duty forklift

Cab view showing the steering position, instrument cluster, display and forward sightline toward the mast.

Build a quotation that can be technically checked

A useful quotation should identify the selected machine and compliance package, not only repeat the rated tonnage.

Load drawingWeight, dimensions, center of gravity, contact points and handling orientation

Mast and attachmentRequired lift height, fork spacing, carriage, beam or other approved attachment

Duty profileMoves per hour, travel distance, shift length, gradients and ambient temperature

Site layoutMinimum aisle, doorway and overhead clearance, pavement and traffic plan

Engine packageExact manufacturer, model, output, emissions level and after-treatment arrangement

Document packageRequested approval records, manuals, drawings and inspection documents

Technical and procurement questions

Is the Euro V Heavy Duty Forklift 25 Ton the same as an EU Stage V forklift?

Do not assume the terms are interchangeable. For an EU non-road project, confirm the exact engine model, power category and applicable Stage V type-approval evidence before ordering.

Does the 25,000 kg rating apply at every load center?

No. The stated rating is at a 1,220 mm load center. A longer, offset or suspended load requires a residual-capacity check using the final mast and attachment load chart.

Is the wide lifting beam shown in the photos standard?

The photos show a project-specific beam with hooks, while the specification lists 2,400 mm forks. Ask the supplier to identify the standard configuration and quote the beam separately when required.

Which diesel engine is available?

The page lists Weichai or Cummins selection with a 160–162 kW power range. The exact model, emissions package and market availability must be confirmed in the project quotation.

What space is needed to operate this 25-ton forklift?

Initial planning should account for the 3,070 mm overall width and 6,480 mm minimum turning radius, then add clearance for the actual load, attachment, traffic routes and safety zones.

What information should be sent for model confirmation?

Send the load drawing and center of gravity, lift height, attachment requirement, yard layout, surface and gradient data, duty cycle, destination country and required emissions documentation.