FD250-P / 25,000 kg Class
Start With the Cargo, Not Only the Tonnage
A 25 ton forklift needs to match the shape of the item sitting on its forks. A steel coil, mould and machine base can fall within a similar weight range while presenting completely different pickup conditions.
For the XINGHAO FD250-P, two useful reference points are the 25-ton class and a 1,220 mm load centre. The next questions are physical: how deep is the piece, where does its mass sit, and from which face can the forks enter?
Useful starting information: send cargo weight, dimensions, pickup direction and centre-of-gravity position when it is known.
FD250-P Reference
Numbers to Place Beside Your Cargo Drawing
The steel-coil version of the FD250-P has a published machine weight of 33,500 kg and overall dimensions of 6680 × 3070 × 3420 mm.
Its listed fork size is 2400 × 285 × 105 mm. The two-stage mast reaches 4,000 mm, while this version uses a 160 kW Cummins diesel engine.
These figures become more meaningful when they are checked against the dimensions of the actual item being moved.
25,000 kg Nominal class
1,220 mm Load centre
33,500 kg Truck weight
2,400 mm Fork length
4,000 mm Lift height
The 1,220 mm Reference
Where Is the Mass Located?
Cargo weight is only one part of the selection check. The published FD250-P data also gives a 1,220 mm load centre.
Imagine two 20-ton pieces. One has a short base with most of its mass close to the carriage. The second extends much farther along the forks. Although the scale reads the same weight, the two pieces do not create the same leverage.
Steel Coil
Record coil weight, outside diameter, width and pickup orientation. This describes the object much more accurately than simply writing "steel coil" on an RFQ.
Die or Mould
Measure the base and mark the centre of gravity if available. An uneven mass distribution should be identified before equipment selection.
Crated Machinery
Show skid depth, fork pockets and any underside obstruction that may limit fork insertion.
If your cargo centre of gravity differs substantially from the published reference condition, send the real dimensions to XINGHAO for technical confirmation.
Fork-to-Cargo Match
What Must the 2,400 mm Forks Reach?
The FD250-P steel-coil version lists forks measuring 2400 × 285 × 105 mm. Fork length alone, however, does not tell whether a particular item can be picked up correctly.
- Measure the available insertion depth beneath the cargo.
- Record fork-pocket spacing when pockets are present.
- Identify blocks, frames or structures below the item.
- Mark the intended approach face.
- Show the known centre-of-gravity position.
For fabricated machinery or irregular steel pieces, even a simple dimensioned drawing can remove ambiguity before the truck specification is finalized.
Steel Coil Handling
Describe the Coil Before Discussing the Truck
Steel coils are a useful example of why tonnage alone is incomplete. Outside diameter and width change the physical relationship between the coil and the lifting equipment.
1. Outside Diameter
Record the coil OD together with its weight. The outside dimensions help establish the cargo envelope during pickup and travel.
2. Coil Width
Width affects how the piece sits relative to the lifting points and should be included in the inquiry drawing.
3. Pickup Direction
State exactly how the coil is approached and supported. A photograph of the existing handling method can be useful.
Lateral Alignment
Small Corrections at the Pickup Point
The current 25-ton product photography includes the truck's side-shift arrangement.
Side shift moves the fork carriage laterally. This helps the driver correct left-to-right alignment without repositioning the entire truck for every small offset.
For repetitive pickup points, provide the cargo width and support layout so the required carriage arrangement can be discussed around the actual workpiece.
Vertical Check
Put the 4,000 mm Mast Into Your Building Drawing
This FD250-P specification uses a two-stage mast with a listed maximum lifting height of 4,000 mm.
Instead of considering that number by itself, compare it with the complete transfer path.
- Receiving platform height
- Cargo height while carried
- Factory doorway height
- Pipework or overhead structures
- Required fork elevation at placement
This dimensional check is particularly useful when a large forklift moves from an outdoor yard into a production building.
FD250-P Data
Published Reference Specifications
The following figures describe the XINGHAO FD250-P steel-coil handling version. Final ordered equipment should be confirmed against the project requirement.
| Item | FD250-P Reference | Buyer Should Provide |
|---|---|---|
| Nominal Class | 25,000 kg | Maximum cargo weight |
| Load Centre | 1,220 mm | Actual cargo C.G. |
| Truck Weight | 33,500 kg | Route or floor restrictions |
| Overall Dimensions | 6680 × 3070 × 3420 mm | Gate and aisle dimensions |
| Fork Size | 2400 × 285 × 105 mm | Fork-entry geometry |
| Mast | 2-stage | Required placement height |
| Maximum Lift Height | 4,000 mm | Overhead clearance |
| Engine | Cummins diesel | Destination requirements |
| Engine Output | 160 kW | Confirm final engine version |
| Emission | Euro 2 / Euro 5 | Required destination standard |
| Transmission | ZF | Confirm ordered specification |
| Front Axle | Dry disc brake | Confirm ordered specification |
| Tyres | Pneumatic, 4 / 2 | Travel-surface information |
Different Cargo, Different Questions
One 25-Tonne Class Does Not Mean One Pickup Pattern
| Workpiece | Measurements to Send | Question to Resolve |
|---|---|---|
| Steel Coil | Weight, OD, width, orientation | Where will the coil be supported? |
| Die / Mould | Weight, footprint, C.G. | Is the mass symmetrical over the fork pair? |
| Crated Machine | Crate size, skid depth, pockets | Can the forks reach the intended support area? |
| Fabricated Steel | Length, width, support points | How far does the piece project forward? |
Actual FD250 Detail Views
Look More Closely at the 25-Ton Machine
The photographs below are taken from the current XINGHAO 25-ton product page. Each image and caption has been kept inside one independent card to prevent the website editor from separating the picture from its description.
Two-Stage 4 m Mast
A closer view of the mast fitted to the photographed 25-ton truck.
2,400 mm Forks
This image shows the long-fork arrangement used on the photographed machine.
Operator Cab
A close view of the cab area on the current 25-ton machine.
Cummins Engine
The current product photography identifies this view as the Cummins engine installation.
Side-Shift Arrangement
A closer look at the carriage-side hardware used for lateral fork alignment.
Before Requesting a Quote
Choose One Representative Cargo Piece
If your factory moves several products, begin with the most difficult recurring piece rather than sending only a target tonnage.
Provide its weight, length, width, height, pickup face, centre of gravity if known, fork-entry dimensions and required placement height. A photograph or dimensioned drawing is especially useful for irregular cargo.
FD250 Buyer Questions
Questions to Answer Before Final Selection
What does the 1,220 mm load centre mean for this FD250?
It is the published load-centre reference for this FD250-P version. If your cargo centre of gravity is positioned differently, send its dimensions and C.G. information for technical review.
What fork size is listed for the FD250-P steel-coil version?
The published FD250-P specification lists forks measuring 2400 × 285 × 105 mm. Actual cargo insertion depth and supporting points should also be checked.
What mast height is shown for this 25 ton forklift?
The referenced FD250-P uses a two-stage mast with a listed maximum lifting height of 4,000 mm.
What information should I provide for steel coil handling?
Provide coil weight, outside diameter, width, pickup orientation, required placement height and the intended supporting method. A dimensioned drawing or photograph can help clarify the pickup geometry.
Does this FD250 version use a Cummins engine?
The referenced FD250-P steel-coil version lists a 160 kW Cummins diesel engine. Confirm the final engine and emission requirement when specifying the ordered machine.
What site dimensions should be checked before ordering?
Compare the truck and carried cargo with gate width, doorway height, travel lanes, turning areas and overhead structures along the intended route.
FD250 Project Check
Send the Cargo Drawing With Your Inquiry
Tell XINGHAO what the truck actually needs to pick up. Include the piece weight, footprint, pickup face, fork-entry dimensions, centre of gravity when available and final placement height.
Discuss Your FD250 RequirementHot Tags: 25 ton forklift, China 25 ton forklift suppliers, factory, Handler Forklift 5t Diesel Forklift Truck, diesel 8 ton counterbalanced forklift, CPCD80, Small 5 Ton Diesel Forklift, 5 Ton Diesel Forklift, Warehouse using Diesel Forklift 3 5 Tonne
